PPPoE Load blancing Mikrotik

This is my configuration in my router mikrotik 2.9.27 using load balancing. This configuration was run successfully in my internet cafe / cybercafe.
[admin@MikroTik] interface> pr
Flags: X – disabled, D – dynamic, R – running
#    NAME                                                TYPE             RX-RATE    TX-RATE    MTU
0  R wan1                                                 ether                   0                  0          1500
1  R wan2                                                 ether                   0                  0          1500
2  R Local                                                 ether                   0                  0          1500
3  R pppoe-out1                                   pppoe-out               0                  0          1480
4  R pppoe-out2                                   pppoe-out               0                  0          1480
[admin@MikroTik] interface>
pppoe-out1  and pppoe-out2  automatic created if your connection running successfull. You only create three interface. Wan1  (speedy1 ) wan2 (speedy) local (local network.
Step 2
Set IP address in all of interface, if your pppoe was ran success full you can saw below new  interface with the name of PPoE-Out
Flags: X – disabled, I – invalid, D – dynamic
#   ADDRESS            NETWORK         BROADCAST       INTERFACE
0   192.168.2.2/25     192.168.2.0     192.168.2.127   wan1
1   192.168.1.200/24   192.168.1.0     192.168.1.255   Local
2   192.168.0.2/25     192.168.0.0     192.168.0.127   wan2
Step 3
Set your nat configuration in ip – firewall -nat
[admin@MikroTik] ip firewall nat> pr
Flags: X – disabled, I – invalid, D – dynamic
0   chain=srcnat out-interface=pppoe-out1 action=masquerade
1   chain=srcnat out-interface=pppoe-out2 action=masquerade
Step 4
Set mark connection in your mangle table  to make load balancing in your router
[admin@MikroTik] ip firewall mangle> pr
Flags: X – disabled, I – invalid, D – dynamic
0   chain=prerouting in-interface=Local connection-state=new nth=1,1,0 action=mark-connection new-connection-mark=satu
passthrough=yes
1   chain=prerouting in-interface=Local connection-mark=satu action=mark-routing new-routing-mark=con_satu passthrough=no
2   chain=prerouting in-interface=Local connection-state=new nth=1,1,1 action=mark-connection new-connection-mark=dua
passthrough=yes
3   chain=prerouting in-interface=Local connection-mark=dua action=mark-routing new-routing-mark=con_dua passthrough=no
Step 5 the last step
Set route.
[admin@MikroTik] ip route> pr
Flags: X – disabled, A – active, D – dynamic, C – connect, S – static, r – rip, b – bgp, o – ospf
#     DST-ADDRESS        PREF-SRC        G GATEWAY         DISTANCE INTERFACE
0 ADC 125.162.34.1/32    125.162.35.220                                                  pppoe-out2
1 ADC 125.162.46.1/32    125.162.47.144                                                   pppoe-out1
2 ADC 192.168.0.0/25     192.168.0.2                                                           wan2
3 ADC 192.168.1.0/24     192.168.1.200                                                       Local
4 ADC 192.168.2.0/25     192.168.2.2                                                            wan1
5 A S 0.0.0.0/0                          r 125.162.46.1                                    1        pppoe-out1
6 A S 0.0.0.0/0                          r 125.162.34.1                                    1        pppoe-out2
7 A S 0.0.0.0/0                          r 125.162.34.1                                    1        pppoe-out2
r 125.162.46.1                                               pppoe-out1
8 A S 0.0.0.0/0                          r 125.162.34.1                                     1        pppoe-out2
That 5 step in my router configuration using load balancing method



sumber : http://nst.web.id/